Maintenance of O-rings is very important to keep your system from experiencing the “F” word, and by the “F” word I mean flood. There is no hard and fast rule on how often they need to be maintained.Housing,Maintenance,Tips,underwater,housing,service,backscatter,support

Underwater Camera Housing Maintenance – Tips to keep your investment safe and running...

O-RINGS: Maintenance of O-rings is very important to keep your system from experiencing the "F" word, and by the "F" word we mean flood. There is no hard and fast rule on how often they need to be maintained. If you are diving in areas with lots of sand like most shore diving areas then you will need to maintain them pretty much every time you open the housing. On boats like live boards then once a day should suffice. O-rings are the barrier that keeps the water away from your camera so their care is extremely important. REMOVAL: Use an O-ring removal tool or the corner of a credit card to ease the O-ring out of its groove. Never, ever use a knife, a pick, or any sharp object to remove the O-ring. Using sharp implements can cause damage to the groove of the housing. You can use two hands by placing a finger on one side of the groove and a second finger about two inches away, then press down and push towards each other which should pop a section out of the groove. Then just use your fingers to pull it out. CLEANING: You should try and clean your O-rings in an area that is free of possible contaminants like sand, hair, lint, etc. Work in a well-lit area. Your fingertips are very sensitive and can detect crud on the O-rings fairly well. Gently pull the O-ring through your fingers which should remove most of the gunk. If you need more cleaning then a dab of dish soap on your fingertips should help clean them. Be careful as they can stretch so don't pull them too hard. LUBRICATION: Your O-ring only needs a light sheen to it. A big problem is that people use too much grease. The grease is a lubricant not a sealant. Grease attracts gunk and hair so use the minimal amount. When you are done make sure nothing has attached itself to the clean O-ring such as hair or fibers. Use the grease your manufacturer recommends. HOUSING: To clean the O-ring groove in the housing we find that the best choice is the small foam makeup applicators you find at beauty supply shops, they are inexpensive and work great. Q-tips tend to leave fibers behind. Once the groove is clean, replace the O-ring making sure it sits properly in the groove. Do a visual check for hair and fibers before sealing up the housing. On the ports, check the threads and do the same O-ring care ritual to make sure they are clean as well. Desiccants are moisture absorbing packets that are useful on polycarbonate (plastic) housings. Condensation occurs inside the housing when you take it from a warm moist environment such as a hot tropical island and then place it into a cooler one like the ocean. The best thing to do is to open and close the housing when you are in your air-conditioned room or cabin not outside. Desiccants will help but not always stop the problem. If you must open it outside blow some dry tank air into the housing before closing it up. Condensation is rarely a problem with aluminum housings. If your housing has an AirLock vacuum system make sure you use it every time you seal the housing, it is the best way to ensure watertight integrity. STROBES & CORDS:Strobes and cords need maintenance too. Clean and lubricate the O-rings like you would your housings O-rings. Clean the threads by scrubbing them lightly with a Wire Brush like an old tooth brush. Don't leave the cords attached for your entire vacation. Check the connections for water entry. Change and recharge your batteries as needed. TIPS: Rinse tanks are friend and foe. A quick dunk before the dive can make sure there are no leaks. Look for bubbles after a few minutes. After the dive, try not to leave your system in the rinse tank. Rinse tanks can get so much use that they can cause your system to get damaged because someone else places their camera on top of yours. A few quick dunks in and out should get most of the salt off. Using soft-sided coolers like those sold in boating stores is a great idea. They give you your own personal rinse tank and padding for your system during the ride to and from the dive site. You don't need to fill them completely. Three or four inches of water are fine. When you are on a dive boat don't forget to let the crew know of any special handling you require for your system to make sure it has a safe trip along with you. When you get home you can fill the bathtub, the soft-sided cooler, or a large storage bin with fresh water and place your system in it for a good soak. Work the controls, buttons, and dials to help loosen up the salt buildup. Dried salt is sharp and can damage the O-rings in the housing controls if not removed. Remove the handles, tray, and strobe arms so nothing gets corroded on. When storing your system for long periods it is a good idea to take it down. You can use an old set of O-rings as storage O-rings. Keep a new set in a zip lock baggie with a little bit of the appropriate O-ring grease smeared inside of it. Change the news ones out for the storage ones before you dive. This will extend the current set you are using. Store the new set inside the housing so you won't forget where they are. FLYING: Do NOT seal the system. You want to remove the O-rings, the port, or leave the back door open so a vacuum does not occur during flight. It is not the best idea to leave your camera inside the housing when you travel. The bumps and bangs your luggage takes can damage the controls or the camera. SERVICE: A two-year interval is a good starting point. The amount of use and the environment where it is used is a factor in when you should get your equipment serviced. Contact our service department if you have any questions. They can be contacted at 1-831-645-1082 or by email: service@backscatter.com, they will be glad to discuss what needs to be done and pricing with you. Safe diving and great shooting...


Related Posts

Our World Underwater Scholarship Society Paul L. Schutt Photography Internship

A few weeks ago, my experience as an underwater photographer had strictly been from behind a GoPro. While I still believe it is one of the best underwater cameras out there, I believed I had reached a...

Read More

Remote Lighting with Backscatter Hybrid Flash & Mini Flash 2 Underwater Guide

One of the standout features of the Hybrid Flash and Mini Flash 2 is Remote Mode. Unlike a simple slave mode, Remote Mode allows for remote triggering and adjustment of power levels on an off-camera H...

Read More

Backscatter Hybrid Flash - How To & Setup Guide

This how-to guide will give you the highlights of the instruction manual in video format. If you’re new to the Hybrid Flash, be sure to check out our comprehensive article on the features of this powe...

Read More

Documenting Marine Conservation with Edwar Herreño

Backscatter pro client and affiliate Edwar Herreno is a marine biologist, technical diving instructor, conservationist, and award-winning freelance underwater photographer and filmmaker. His work has ...

Read More

What Is The Best Aperture For Underwater Photography & Video?

What is the best aperture for underwater photos and videos? During The Digital Shootout, we asked a panel of the world’s best underwater photographers and videographers this question to get their hot-...

Read More

What Is The Best ISO For Underwater Photography & Video?

What is the best ISO for underwater photos and videos? During The Digital Shootout, we asked a panel of the world’s best underwater photographers and videographers this question to get their hot-take ...

Read More